Nissan Qashqai e-POWER 2023 Owners Manual
7.8.5.1. Bluetooth® settings
To pair a device, make sure the Bluetooth is switched on and use the [Scan devices] key or the [Pair device] key. For details, see
.When an Apple device is connected via the USB connection port and Bluetooth, the device will be recognised as a USB device. The battery of the Apple device is charged while the cable is connected to the USB connection port.
Up to 5 different Bluetooth devices can be connected. However, only one device can be used at a time. If 5 different Bluetooth registered devices are registered, a new device can only replace one of the 5 existing paired devices. Use [Del. device] key to delete one of the existing paired devices. For details, see
.When successfully paired a notification message will be displayed, then the audio system display will return to the current audio source display. During connection the following status icons will be displayed (top left of the display): Signal strength (
), Battery status* (
) and Bluetooth ON (
).
*: If the low battery message comes on, the Bluetooth® device must be recharged soon.
The pairing procedure and operation may vary according to device type and compatibility. See the Bluetooth® owner’s manual for further details.
For device details, see your audio/mobile phone Owner's Manual.
For assistance with the Bluetooth® audio/mobile phone integration, please visit your local NISSAN dealer or qualified workshop.
To set up the Bluetooth system with a device the following items are available:
[Scan devices]
Shows all available visible BT devices and initialises BT connection.
[Pair device]
Bluetooth devices can be paired with the system. A maximum of 5 Bluetooth devices can be registered.
[Sel. device]
Paired Bluetooth devices are listed and can be selected for connection.
[Del. device]
A registered Bluetooth device can be deleted.
[Bluetooth]
If this setting is turned off, the connection between the Bluetooth devices and the in-vehicle Bluetooth module will be cancelled.
[Scan devices]
Press the
button. Select [Scan devices].The audio unit searches Bluetooth devices and shows all visible devices. Pressing the <BACK> button cancels the search.
Make sure your Bluetooth device is visible at this time. The audio unit will wait for a connection request from the Bluetooth device.
Select the device to be paired.
Use the <MENU> dial and press <OK> to select.
The pairing procedure may depend on the device to be connected:
Device without PIN code:
The Bluetooth connection will be automatically connected without any further input.
Device with PIN code:
Two different ways of pairing are possible depending on the device:
Type A:
The message [To pair] [Enter Pin] 0000 will be displayed.
Confirm the PIN code on the device and the audio unit.
The Bluetooth connection will be made.
If the countdown timer reaches 0, the attempt to pair the device will be cancelled.
Type B:
The message [Pairing request] [Confirm password] together with a 6 digit code will be displayed. The unique and identical code should be displayed on the device. If the code is identical confirm on the device and on the audio unit.
The Bluetooth connection will be made.
Pair device
Turn on the Bluetooth® on the audio unit. See
.Use the Bluetooth® audio device/mobile phone to pair:
Switch on the search mode for Bluetooth® devices. If the search mode finds the audio unit, it will be shown on the device display.
Select the unit device shown as [My Car].
Two different ways of pairing are possible depending on the device. For the correct procedure details, see
.
When an Apple device is connected via the USB connection port and Bluetooth®, the device will be recognised as a USB device. The battery of the Apple device is charged while the cable is connected to the USB connection port.
[Sel. device]
The paired device list shows which Bluetooth® audio or mobile phone devices have been paired or registered with the Bluetooth® audio system. If the list contains devices then select the appropriate device to connect to the Bluetooth® audio system.
The following symbols (where fitted) indicate the capability of the registered device:
- : Mobile phone integration
: Audio streaming (A2DP – Advanced Audio Distribution Profile)
[Del. device]
A registered device can be removed from the Bluetooth audio system. Select a registered device then press <OK> to confirm to deletion.
[Bluetooth]
If Bluetooth® has been switched off a notification message [ON/OFF] appears when you select [Bluetooth] from the phone menu (press ). To switch the Bluetooth® signal on, press <OK> and a follow up screen will appear. Then select [ON] and press ${2} to display the Bluetooth® settings menu screen.