Nissan ARIYA 2024 Owners Manual

5.4.6.2. Installation on front passenger's seat

imageimage
  • Never install a rear-facing child restraint on the front passenger seat without ensuring that the front passenger air bag is deactivated. The vehicle is equipped with an automatic front-passenger front air bag deactivation system. The <PASSENGER AIR BAG OFF> indicator lightimage, located on the roof console, must be lit. In a frontal collision, supplemental front-impact air bags inflate with great force. An inflating supplemental front-impact air bag could seriously injure or kill your child.

  • Never install a child restraint with a top tether strap on the front seat.

  • NISSAN recommends that a child restraint be installed on the rear seat. However, if you must install a child restraint on the front passenger's seat, move the passenger's seat to the rearmost position.

  • Child restraints for infants must be used in the rear-facing direction and therefore must not be used on the front passenger's seat when the front passenger's air bag has not been deactivated.

  • Failure to use the seat belts will result in the child restraint not being properly secured. It could tip over or otherwise be unsecured and cause injury to the child in a sudden stop or collision.

Front-facing

Be sure to follow the manufacturer’s instructions for the proper use of your child restraint. Follow these steps to install a front-facing child restraint on the front passenger’s seat using a three-point type seat belt.

If the child restraint is installed on the front passenger seat, place the power switch in the ON position. The front passenger air bag status light <PASSENGER AIR BAG OFF>, located on the roof console, should illuminate. If this light is not illuminated, see

. Move the child restraint to another seating position. Have the system checked by a NISSAN certified electric vehicle dealer.
imageimage
  1. Move the seat to the rearmost position (1).

  2. Adjust or remove the head restraint (2) to obtain the correct child restraint fit.

  3. Position the child restraint in the seat.

    Always follow the child restraint system manufacturer's instructions for installation and use.

    image
  4. Route the seat belt tongue through the child restraint and insert it into the buckle (3) until you hear and feel the latch engage.

  5. To prevent slack in the seat belt webbing, it is necessary to secure the seat belt in place with locking devices attached to the child restraint.

    image
  6. Remove any additional slack from the seat belt; press downward (4) and rearward (5) firmly in the centre of the child restraint with your knee to compress the vehicle seat cushion and seatback while pulling up on the seat belt.

    image
  7. Test the child restraint before you place the child in it (6). Push the child restraint from side to side and tug it forward to make sure that it is held securely in place.

  8. Check to make sure that the child restraint is properly secured prior to each use. If the child restraint is loose, repeat steps 5 through 7.

    If the child restraint is still loose, do not use it. Please check the child restraint system manufacturer's instructions for installation and use. Seek advice from a NISSAN certified electric vehicle dealer.

  9. Place the power switch in the ON position. Check the front passenger air bag status light located on the roof console. The front passenger air bag status light image (OFF) should illuminate.

Rear-facing

If you must install a child restraint in the front passenger's seat, follow these steps:

image
  1. If the child restraint is installed on the front passenger seat, place the power switch in the ON position. The <PASSENGER AIR BAG OFF> lightimage, located on the roof console, should illuminate. If the <PASSENGER AIR BAG ON> lightimage is illuminated, see

    . Move the child restraint to another seating position. Have the system checked by a NISSAN certified electric vehicle dealer.
    image
  2. Move the seat to the rearmost position (1).

  3. Position the child restraint in the seat.

    Always follow the child restraint system manufacturer's instructions for installation and use.

    image
  4. Route the seat belt tongue through the child restraint and insert it into the buckle until you hear and feel the latch engage.

    To prevent slack in the lap belt, secure the shoulder belt in place with a locking clip (A). Use a locking clip attached to the child restraint, or one which is equivalent in dimensions and strength.

    Be sure to follow the child restraint system manufacturer's instructions for belt routing.

  5. Slide the seat forwards so that the seat belt fully tightens the child restraint and the child restraint reaches the vehicle dashboard.

  6. Test the child restraint before you place the child in it. Check that it does not tilt too far from side to side. Try to tug it forwards and check if it is held securely in place.

    If the child restraint is still not securely held in place, do not use it. Please check the child restraint system manufacturer's instructions for installation and use. Seek advice from a NISSAN certified electric vehicle dealer for correct child restraint installation.

Parent topic: