Nissan Qashqai e-POWER 2023 Owners Manual
8.21.9.1. ProPILOT Assist Speed limiter operations
- <CANCEL> switch
- A)<RES+> (Resume) switch
- B)<SET–> (Set) switch
- Speed limiter main “ON/OFF” switch (where fitted)
- ProPILOT Assist switch
- Speed limiter symbol
- Set speed value
Turning the speed limiter on
The speed limiter can be switched on after the e-POWER system is started or when driving.
Push the speed limiter main “ON/OFF” switch (2).
The speed limiter symbol (4) and the set speed value (5) will illuminate in the Vehicle Information Display.
Turning the Speed limiter system on will turn on the Intelligent Lane Intervention (ILI) and Intelligent Blind Spot Intervention systems at the same time, providing those systems are enabled in the [Driver Assistance] menu in the vehicle information display. For additional information, see
and .Setting speed limit
Push the <SET–> switch.
The speed limit will be set at the current speed.
When driving less than 30 km/h (20 MPH), the speed limiter will be set to the minimum possible set speed of 30 km/h (20 MPH).
When the speed limit is set, the speed limiter symbol (4) and the set speed value (5) will turn green.
Changing a speed limit
Use either of the following operations to change an active speed limit:
Push and release the <RES+> (Resume) switch or <SET–> switch. Each time you do this, the set speed will increase or decrease by 1 km/h (1 MPH).
Push and hold the <RES+> (Resume) switch or <SET–> switch. The set speed will increase or decrease to the next multiple of 5 km/h (5 MPH) and then in steps of 5 km/h (5 MPH).
The new set speed limit value (5) will be displayed in the Vehicle Information Display.
When the actual vehicle speed exceeds the set speed, an audible warning will be heard a short time after the set speed is exceeded and driver intervention is not detected.
Cancelling a speed limit
To cancel a set speed limit, push the <CANCEL> switch . The speed limiter symbol (4) and the set speed value (5) in the Vehicle Information Display will turn grey.
It is also possible to override the speed limiter by fully depressing the accelerator pedal beyond the resistance point.
The vehicle may accelerate when the speed limiter cancels.
When additional floor mats are used, be sure that they are correctly secured and that they cannot interfere with the accelerator pedal. Mats not adapted to the vehicle may prevent proper operation of the speed limiter.
Fully depress the accelerator pedal beyond the resistance point. The speed limiter will be suspended to allow driving above the set speed. The set speed value (5) will flash and an audible warning will sound. The speed limiter will automatically resume when the vehicle speed drops below the set speed limit.
Resuming a previous set speed
If a set speed limit has been cancelled, the set speed will be stored in the speed limiter memory.
This speed limit can be reactivated by pressing the <RES+> (Resume) switch (A).
If the current vehicle speed is higher than the previous set speed, the accelerator pedal will not work and the set speed value (5) will flash until the vehicle speed drops below the set speed limit.
When the actual vehicle speed exceeds the set speed, an audible warning will be heard a short time after the set speed is exceeded and driver intervention is not detected.
Turning the speed limiter off
The speed limiter system will be turned off when one of the following operations is performed:
Push the speed limiter main “ON/OFF” switch. The speed limiter symbol (4) and the set speed value (5) in the Vehicle Information Display will be turned off.
Push the blue ProPILOT Assist “ON/OFF” switch. The speed limiter information in the vehicle information will be replaced with the ProPILOT Assist display. For details see
.When the vehicle is stopped and the power switch is switched OFF.
Turning off the speed limiter will erase the set speed limit memory.
Speed limiter malfunction
If the speed limiter malfunctions, the speed limiter symbol (4) in the Vehicle Information Display will flash.
Turn the speed limiter off by pushing the speed limiter main “ON/OFF” switch (3) and have the system checked by a NISSAN dealer or qualified workshop.