Nissan Qashqai e-POWER 2023 Owners Manual

8.20.3.16. Speed Limit Link - ICC with Navigation system (where fitted)

image

Listed below are the system limitations for the Speed Limit Link. Failure to operate the vehicle in accordance with these system limitations could result in serious injury or death:

  • It is the driver’s responsibility to select the proper speed, follow all traffic regulations and observe other road users.

  • The Speed Limit Link may not operate properly and the actual speed limit may not be applied to the vehicle set speed in all conditions. The driver must manually control the vehicle speed.

    Below are some examples:

    • When the Traffic Sign Recognition (TSR) system is not functioning properly or turned off. (See

      .)
    • When driving in countries or areas not covered by the navigation system.

    • When crossing national boundaries.

    • When driving on the exit of the limited access motorway as identified in the navigation map data.

    • When driving in an area with nearby parallel roads (for example, motorway with a parallel service drive).

    • When driving in an area where each lane has a different speed limit sign.

    • When driving on a road under construction or in a construction zone.

    • When the data from the navigation system is not up-to-date or is unavailable.

When the ICC Speed Limit Link is active and it detects a change of the speed limit, the new speed limit is indicated and it can be applied to the vehicle set speed manually.

The Speed Limit Link operates:

  • When the detected speed limit is 30 km/h (20 MPH) and above.

  • The [Speed Limit Link] is enabled in the settings menu of the vehicle information display.

image
  • In the following situations, the Speed Limit Link will not operate:

    • When an increase in the posted speed limit is detected, but the vehicle set speed is already faster than the new speed limit.

    • When a decrease in the posted speed limit is detected, but the vehicle set speed is already lower than the new speed limit.

For Germany: No Limit speed setting

When you switch on the e-POWER system and subsequently enter a motorway with no speed limit, the system initially regulates the speed to 130 km/ h. After this, the last speed stored by the driver on a motorway with no speed limit is applied.

image

This feature only works in Germany.

System display and indicators

image
  1. Detected speed limit indicator

    Displays the currently detected speed limit. For additional information, see

    .
  2. Applied speed limit indicator (green frame)

    Indicates the detected speed limit can be applied to the vehicle set speed.

  3. Speed Limit Link indicator

    Indicates the system activation mode or system operation.

    image Manual mode is activated and a new speed limit (faster speed value) is indicated.

    image Manual mode is activated and a new speed limit (lower speed value) is indicated.

  4. Guidance message, instruction on how to set new speed.

Operating the system

When the system detects a different speed limit, the new speed value is indicated. The vehicle set speed can be changed to the indicated speed limit manually.

  • To accept the newly indicated speed limit, operate the <RES+> switch (in case of speed limit up) or <SET-> switch (in case of speed limit down).

  • The Speed Limit Link indicator (image or image) will turn off after approximately 15 seconds if the <RES+> or <SET-> switch is not operated. (The Speed Limit Link indicator can be turned off immediately by operating the opposite switch from the direction indicated by the Speed Limit Link indicator.)

The system will not activate if a speed limit change is not detected.

[Speed Link Offset]

It is possible to set whether the speed limit should be accepted exactly, or with a tolerance of -10 km/h (–5 MPH) to +10 km/h (+5 MPH)

How to activate or deactivate the system

  1. Push the imageimage button on the steering wheel until [Settings] appears in the vehicle information display, and push the scroll dial.

  2. Use the scroll dial to select [Driver Assistance]. Then push the scroll dial.

  3. Select [Speed Limit Link], and push the scroll dial to turn the system on or off.

To deactivate the system, select [OFF].

image

The system will retain current settings in the vehicle information display even if the e-POWER system is restarted.

How to set tolerance for [Speed Link Offset]

  1. Push the imageimage button on the steering wheel until [Settings] appears in the vehicle information display, and push the scroll dial.

  2. Use the scroll dial to select [Driver Assistance]. Then push the scroll dial.

  3. Select [Speed Link Offset] , and push the scroll dial to select tolerance value.

image

The system will retain current settings in the vehicle information display even if the e-POWER system is restarted.

Parent topic: